# generated by SuperSlicer 2.3.56 on 2021-09-11 at 23:38:24 UTC

[print:0.20mm QUALITY - Makerbot]
allow_empty_layers = 0
avoid_crossing_not_first_layer = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = rectilinear
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.5
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 95%
bridge_overlap = 100%
bridge_speed = 30
bridge_speed_internal = 150%
bridged_infill_margin = 200%
brim_ears = 0
brim_ears_detection_length = 1
brim_ears_max_angle = 125
brim_ears_pattern = concentric
brim_inside_holes = 0
brim_offset = 0
brim_width = 0
brim_width_interior = 0
clip_multipart_objects = 1
compatible_printers = "Dual Extruders";"Left Extruder";"Right Extruder"
compatible_printers_condition = 
complete_objects = 0
complete_objects_one_skirt = 0
complete_objects_sort = object
curve_smoothing_angle_concave = 0
curve_smoothing_angle_convex = 0
curve_smoothing_cutoff_dist = 2
curve_smoothing_precision = 0
default_acceleration = 1000
dont_support_bridges = 1
draft_shield = 0
duplicate_distance = 6
enforce_full_fill_volume = 1
ensure_vertical_shell_thickness = 1
exact_last_layer_height = 0
external_infill_margin = 150%
external_perimeter_cut_corners = 0%
external_perimeter_extrusion_spacing = 
external_perimeter_extrusion_width = 0.45
external_perimeter_overlap = 100%
external_perimeter_speed = 25
external_perimeters_first = 0
external_perimeters_hole = 1
external_perimeters_nothole = 1
external_perimeters_vase = 0
extra_perimeters = 0
extra_perimeters_odd_layers = 0
extra_perimeters_overhangs = 0
extruder_clearance_height = 20
extruder_clearance_radius = 45
extrusion_spacing = 
extrusion_width = 0.45
fill_angle = 45
fill_angle_increment = 0
fill_density = 15%
fill_pattern = grid
fill_smooth_distribution = 10%
fill_smooth_width = 50%
fill_top_flow_ratio = 100%
first_layer_acceleration = 1000
first_layer_extrusion_spacing = 
first_layer_extrusion_width = 0.42
first_layer_flow_ratio = 100%
first_layer_height = 0.2
first_layer_infill_speed = 30
first_layer_size_compensation = -0.2
first_layer_speed = 20
gap_fill = 1
gap_fill_min_area = 100%
gap_fill_overlap = 100%
gap_fill_speed = 40
gcode_comments = 0
gcode_label_objects = 1
hole_size_compensation = 0
hole_size_threshold = 100
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
infill_acceleration = 1000
infill_anchor = 2.5
infill_anchor_max = 12
infill_connection = connected
infill_connection_bottom = connected
infill_connection_solid = connected
infill_connection_top = connected
infill_dense = 0
infill_dense_algo = autoenlarged
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_spacing = 
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 80
inherits = 
interface_shells = 0
ironing = 0
ironing_angle = -1
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 100
max_volumetric_speed = 0
milling_after_z = 200%
milling_extra_size = 150%
milling_post_process = 0
milling_speed = 30
min_skirt_length = 4
min_width_top_surface = 200%
model_precision = 0.0001
no_perimeter_unsupported_algo = none
notes = 
only_one_perimeter_top = 1
only_one_perimeter_top_other_algo = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
over_bridge_flow_ratio = 120%
overhangs_reverse = 0
overhangs_reverse_threshold = 250%
overhangs_speed = 100%
overhangs_width = 75%
overhangs_width_speed = 0
perimeter_acceleration = 800
perimeter_bonding = 0%
perimeter_extruder = 1
perimeter_extrusion_spacing = 
perimeter_extrusion_width = 0.45
perimeter_loop = 0
perimeter_loop_seam = rear
perimeter_overlap = 100%
perimeter_round_corners = 0
perimeter_speed = 45
perimeters = 2
post_process = 
print_extrusion_multiplier = 100%
print_retract_length = -1
print_retract_lift = -1
print_settings_id = 
print_temperature = 0
raft_layers = 0
resolution = 0.002
seam_angle_cost = 100%
seam_position = cost
seam_travel_cost = 20%
single_extruder_multi_material_priming = 0
skirt_distance = 6
skirt_extrusion_width = 0
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_max_length = 20
small_perimeter_min_length = 6
small_perimeter_speed = 25
solid_fill_pattern = rectilineargapfill
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_spacing = 
solid_infill_extrusion_width = 0.45
solid_infill_speed = 80
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance_bottom = 0.1
support_material_contact_distance_top = 0.1
support_material_contact_distance_type = filament
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0.2
support_material_interface_speed = 80%
support_material_pattern = rectilinear
support_material_solid_first_layer = 0
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 55
support_material_with_sheath = 0
support_material_xy_spacing = 50%
thin_perimeters = 1
thin_perimeters_all = 0
thin_walls = 1
thin_walls_merge = 1
thin_walls_min_width = 50%
thin_walls_overlap = 50%
thin_walls_speed = 30
threads = 8
top_fill_pattern = smooth
top_infill_extrusion_spacing = 
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 40
top_solid_layers = 5
top_solid_min_thickness = 0.7
travel_speed = 180
travel_speed_z = 0
wipe_tower = 1
wipe_tower_bridging = 10
wipe_tower_brim = 150%
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 170
wipe_tower_y = 125
xy_inner_size_compensation = 0
xy_size_compensation = 0

[print:0.20mm SPEED - Makerbot]
allow_empty_layers = 0
avoid_crossing_not_first_layer = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = rectilinear
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.5
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 95%
bridge_overlap = 100%
bridge_speed = 30
bridge_speed_internal = 150%
bridged_infill_margin = 200%
brim_ears = 0
brim_ears_detection_length = 1
brim_ears_max_angle = 125
brim_ears_pattern = concentric
brim_inside_holes = 0
brim_offset = 0
brim_width = 0
brim_width_interior = 0
clip_multipart_objects = 1
compatible_printers = "Dual Extruders";"Left Extruder";"Right Extruder"
compatible_printers_condition = 
complete_objects = 0
complete_objects_one_skirt = 0
complete_objects_sort = object
curve_smoothing_angle_concave = 0
curve_smoothing_angle_convex = 0
curve_smoothing_cutoff_dist = 2
curve_smoothing_precision = 0
default_acceleration = 1000
dont_support_bridges = 1
draft_shield = 0
duplicate_distance = 6
enforce_full_fill_volume = 1
ensure_vertical_shell_thickness = 1
exact_last_layer_height = 0
external_infill_margin = 150%
external_perimeter_cut_corners = 0%
external_perimeter_extrusion_spacing = 
external_perimeter_extrusion_width = 0.45
external_perimeter_overlap = 100%
external_perimeter_speed = 35
external_perimeters_first = 0
external_perimeters_hole = 1
external_perimeters_nothole = 1
external_perimeters_vase = 0
extra_perimeters = 0
extra_perimeters_odd_layers = 0
extra_perimeters_overhangs = 0
extruder_clearance_height = 20
extruder_clearance_radius = 45
extrusion_spacing = 
extrusion_width = 0.45
fill_angle = 45
fill_angle_increment = 0
fill_density = 20%
fill_pattern = grid
fill_smooth_distribution = 10%
fill_smooth_width = 50%
fill_top_flow_ratio = 100%
first_layer_acceleration = 1000
first_layer_extrusion_spacing = 
first_layer_extrusion_width = 0.42
first_layer_flow_ratio = 100%
first_layer_height = 0.2
first_layer_infill_speed = 30
first_layer_size_compensation = -0.2
first_layer_speed = 20
gap_fill = 1
gap_fill_min_area = 100%
gap_fill_overlap = 100%
gap_fill_speed = 40
gcode_comments = 0
gcode_label_objects = 1
hole_size_compensation = 0
hole_size_threshold = 100
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
infill_acceleration = 1000
infill_anchor = 2.5
infill_anchor_max = 12
infill_connection = connected
infill_connection_bottom = connected
infill_connection_solid = connected
infill_connection_top = connected
infill_dense = 0
infill_dense_algo = autoenlarged
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_spacing = 
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 100
inherits = 
interface_shells = 0
ironing = 0
ironing_angle = -1
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 100
max_volumetric_speed = 0
milling_after_z = 200%
milling_extra_size = 150%
milling_post_process = 0
milling_speed = 30
min_skirt_length = 4
min_width_top_surface = 200%
model_precision = 0.0001
no_perimeter_unsupported_algo = none
notes = 
only_one_perimeter_top = 1
only_one_perimeter_top_other_algo = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
over_bridge_flow_ratio = 120%
overhangs_reverse = 0
overhangs_reverse_threshold = 250%
overhangs_speed = 100%
overhangs_width = 75%
overhangs_width_speed = 0
perimeter_acceleration = 800
perimeter_bonding = 0%
perimeter_extruder = 1
perimeter_extrusion_spacing = 
perimeter_extrusion_width = 0.45
perimeter_loop = 0
perimeter_loop_seam = rear
perimeter_overlap = 100%
perimeter_round_corners = 0
perimeter_speed = 60
perimeters = 2
post_process = 
print_extrusion_multiplier = 100%
print_retract_length = -1
print_retract_lift = -1
print_settings_id = 
print_temperature = 0
raft_layers = 0
resolution = 0.002
seam_angle_cost = 100%
seam_position = cost
seam_travel_cost = 20%
single_extruder_multi_material_priming = 0
skirt_distance = 6
skirt_extrusion_width = 0
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_max_length = 20
small_perimeter_min_length = 6
small_perimeter_speed = 25
solid_fill_pattern = rectilineargapfill
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_spacing = 
solid_infill_extrusion_width = 0.45
solid_infill_speed = 100
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance_bottom = 0.1
support_material_contact_distance_top = 0.1
support_material_contact_distance_type = filament
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0.2
support_material_interface_speed = 80%
support_material_pattern = rectilinear
support_material_solid_first_layer = 0
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 55
support_material_with_sheath = 0
support_material_xy_spacing = 50%
thin_perimeters = 1
thin_perimeters_all = 0
thin_walls = 1
thin_walls_merge = 1
thin_walls_min_width = 50%
thin_walls_overlap = 50%
thin_walls_speed = 30
threads = 8
top_fill_pattern = smooth
top_infill_extrusion_spacing = 
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 50
top_solid_layers = 5
top_solid_min_thickness = 0.7
travel_speed = 180
travel_speed_z = 0
wipe_tower = 1
wipe_tower_bridging = 10
wipe_tower_brim = 150%
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 170
wipe_tower_y = 125
xy_inner_size_compensation = 0
xy_size_compensation = 0

[print:0.30mm DRAFT - Makerbot]
allow_empty_layers = 0
avoid_crossing_not_first_layer = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = rectilinear
bottom_solid_layers = 3
bottom_solid_min_thickness = 0.5
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 95%
bridge_overlap = 100%
bridge_speed = 30
bridge_speed_internal = 150%
bridged_infill_margin = 200%
brim_ears = 0
brim_ears_detection_length = 1
brim_ears_max_angle = 125
brim_ears_pattern = concentric
brim_inside_holes = 0
brim_offset = 0
brim_width = 0
brim_width_interior = 0
clip_multipart_objects = 1
compatible_printers = "Dual Extruders";"Left Extruder";"Right Extruder"
compatible_printers_condition = 
complete_objects = 0
complete_objects_one_skirt = 0
complete_objects_sort = object
curve_smoothing_angle_concave = 0
curve_smoothing_angle_convex = 0
curve_smoothing_cutoff_dist = 2
curve_smoothing_precision = 0
default_acceleration = 1000
dont_support_bridges = 1
draft_shield = 0
duplicate_distance = 6
enforce_full_fill_volume = 1
ensure_vertical_shell_thickness = 1
exact_last_layer_height = 0
external_infill_margin = 150%
external_perimeter_cut_corners = 0%
external_perimeter_extrusion_spacing = 
external_perimeter_extrusion_width = 0.6
external_perimeter_overlap = 100%
external_perimeter_speed = 35
external_perimeters_first = 0
external_perimeters_hole = 1
external_perimeters_nothole = 1
external_perimeters_vase = 0
extra_perimeters = 0
extra_perimeters_odd_layers = 0
extra_perimeters_overhangs = 0
extruder_clearance_height = 20
extruder_clearance_radius = 45
extrusion_spacing = 
extrusion_width = 0.5
fill_angle = 45
fill_angle_increment = 0
fill_density = 20%
fill_pattern = grid
fill_smooth_distribution = 10%
fill_smooth_width = 50%
fill_top_flow_ratio = 100%
first_layer_acceleration = 1000
first_layer_extrusion_spacing = 
first_layer_extrusion_width = 0.42
first_layer_flow_ratio = 100%
first_layer_height = 0.2
first_layer_infill_speed = 30
first_layer_size_compensation = -0.2
first_layer_speed = 20
gap_fill = 1
gap_fill_min_area = 100%
gap_fill_overlap = 100%
gap_fill_speed = 40
gcode_comments = 0
gcode_label_objects = 1
hole_size_compensation = 0
hole_size_threshold = 100
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
infill_acceleration = 1000
infill_anchor = 2.5
infill_anchor_max = 12
infill_connection = connected
infill_connection_bottom = connected
infill_connection_solid = connected
infill_connection_top = connected
infill_dense = 0
infill_dense_algo = autoenlarged
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_spacing = 
infill_extrusion_width = 0.5
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 85
inherits = 
interface_shells = 0
ironing = 0
ironing_angle = -1
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.3
max_print_speed = 100
max_volumetric_speed = 0
milling_after_z = 200%
milling_extra_size = 150%
milling_post_process = 0
milling_speed = 30
min_skirt_length = 4
min_width_top_surface = 200%
model_precision = 0.0001
no_perimeter_unsupported_algo = none
notes = 
only_one_perimeter_top = 1
only_one_perimeter_top_other_algo = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
over_bridge_flow_ratio = 120%
overhangs_reverse = 0
overhangs_reverse_threshold = 250%
overhangs_speed = 100%
overhangs_width = 75%
overhangs_width_speed = 0
perimeter_acceleration = 800
perimeter_bonding = 0%
perimeter_extruder = 1
perimeter_extrusion_spacing = 
perimeter_extrusion_width = 0.5
perimeter_loop = 0
perimeter_loop_seam = rear
perimeter_overlap = 100%
perimeter_round_corners = 0
perimeter_speed = 50
perimeters = 2
post_process = 
print_extrusion_multiplier = 100%
print_retract_length = -1
print_retract_lift = -1
print_settings_id = 
print_temperature = 0
raft_layers = 0
resolution = 0.002
seam_angle_cost = 100%
seam_position = cost
seam_travel_cost = 20%
single_extruder_multi_material_priming = 0
skirt_distance = 6
skirt_extrusion_width = 0
skirt_height = 3
skirts = 1
slice_closing_radius = 0.049
small_perimeter_max_length = 20
small_perimeter_min_length = 6
small_perimeter_speed = 30
solid_fill_pattern = rectilineargapfill
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_spacing = 
solid_infill_extrusion_width = 0.5
solid_infill_speed = 80
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance_bottom = 0.1
support_material_contact_distance_top = 0.1
support_material_contact_distance_type = filament
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.38
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0.2
support_material_interface_speed = 80%
support_material_pattern = rectilinear
support_material_solid_first_layer = 0
support_material_spacing = 2
support_material_speed = 45
support_material_synchronize_layers = 0
support_material_threshold = 55
support_material_with_sheath = 0
support_material_xy_spacing = 50%
thin_perimeters = 1
thin_perimeters_all = 0
thin_walls = 1
thin_walls_merge = 1
thin_walls_min_width = 50%
thin_walls_overlap = 50%
thin_walls_speed = 30
threads = 8
top_fill_pattern = smooth
top_infill_extrusion_spacing = 
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 40
top_solid_layers = 4
top_solid_min_thickness = 0.7
travel_speed = 180
travel_speed_z = 0
wipe_tower = 1
wipe_tower_bridging = 10
wipe_tower_brim = 150%
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 170
wipe_tower_y = 125
xy_inner_size_compensation = 0
xy_size_compensation = 0

[filament:Generic ABS - Makerbot]
bed_temperature = 110
bridge_fan_speed = 25
chamber_temperature = 0
compatible_printers = "Dual Extruders";"Left Extruder";"Right Extruder"
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 4
end_filament_gcode = "; Filament-specific end gcode"
external_perimeter_fan_speed = -1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 30
filament_colour = #FFF2EC
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 27.82
filament_density = 1.04
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_speed = 0
filament_max_volumetric_speed = 11
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_shrink = 100%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = ABS
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = Generic
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
first_layer_bed_temperature = 100
first_layer_temperature = 255
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 15
max_speed_reduction = 90%
min_fan_speed = 15
min_print_speed = 15
slowdown_below_layer_time = 20
start_filament_gcode = ""
temperature = 255
top_fan_speed = -1

[filament:Generic FLEX - Makerbot]
bed_temperature = 50
bridge_fan_speed = 80
chamber_temperature = 0
compatible_printers = "Dual Extruders";"Left Extruder";"Right Extruder"
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
external_perimeter_fan_speed = -1
extrusion_multiplier = 1.15
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #008000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 82
filament_density = 1.22
filament_deretract_speed = 25
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_speed = 0
filament_max_volumetric_speed = 1.2
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_shrink = 100%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = FLEX
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = Generic
filament_wipe = 0
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
first_layer_bed_temperature = 50
first_layer_temperature = 240
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 90
max_speed_reduction = 90%
min_fan_speed = 70
min_print_speed = 15
slowdown_below_layer_time = 15
start_filament_gcode = ""
temperature = 240
top_fan_speed = -1

[filament:Generic PETG - Makerbot]
bed_temperature = 90
bridge_fan_speed = 50
chamber_temperature = 0
compatible_printers = "Dual Extruders";"Left Extruder";"Right Extruder"
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
external_perimeter_fan_speed = -1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 27.82
filament_density = 1.27
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_speed = 0
filament_max_volumetric_speed = 8
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 1.4
filament_retract_lift = 0.2
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_shrink = 100%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = PETG
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = Generic
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
first_layer_bed_temperature = 85
first_layer_temperature = 230
full_fan_speed_layer = 5
inherits = 
max_fan_speed = 50
max_speed_reduction = 90%
min_fan_speed = 30
min_print_speed = 15
slowdown_below_layer_time = 15
start_filament_gcode = ""
temperature = 240
top_fan_speed = -1

[filament:Generic PLA - Makerbot]
bed_temperature = 55
bridge_fan_speed = 100
chamber_temperature = 0
compatible_printers = "Dual Extruders";"Left Extruder";"Right Extruder"
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
external_perimeter_fan_speed = -1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 25.4
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_speed = 0
filament_max_volumetric_speed = 15
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_shrink = 100%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = Generic
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
first_layer_bed_temperature = 55
first_layer_temperature = 205
full_fan_speed_layer = 4
inherits = 
max_fan_speed = 100
max_speed_reduction = 90%
min_fan_speed = 100
min_print_speed = 15
slowdown_below_layer_time = 15
start_filament_gcode = ""
temperature = 200
top_fan_speed = -1

[printer:Dual Extruders]
bed_custom_model = 
bed_custom_texture = 
bed_shape = -112.5x-72.5,112.5x-72.5,112.5x72.5,-112.5x72.5
before_layer_gcode = 
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = 
default_print_profile = 
deretract_speed = 0,0
end_gcode = ; **** begin end.gcode Replicator 1 Dual ****\nM73 P100; end build progress\nM127; disable fan\nM140 S0 T0; set bed temperature to 0\nM104 S0 T0; set right extruder temperature to 0\nM104 S0 T1; set left extruder temperature to 0\nG1 Z150 F1100 ; send Z axis to bottom of machine\nT0 ; Next job assumes T0 is the current tool\nM18; disable all stepper motors\nM70 P5 (PRINT COMPLETE)\nM72 P1; Play Ta-Da song\n; **** end end.gcode ****
extra_loading_move = -2
extruder_colour = ;
extruder_fan_offset = 0%,0%
extruder_offset = 0x0,0x0
extruder_temperature_offset = 0,0
fan_kickstart = 0
fan_percentage = 0
fan_speedup_overhangs = 1
fan_speedup_time = 0
feature_gcode = 
gcode_flavor = reprapfirmware
gcode_precision_e = 5,5
gcode_precision_xyz = 3
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 10000,5000
machine_max_acceleration_extruding = 1500,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_travel = 1500,1250
machine_max_acceleration_x = 9000,1000
machine_max_acceleration_y = 9000,1000
machine_max_acceleration_z = 500,200
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 500,200
machine_max_feedrate_y = 500,200
machine_max_feedrate_z = 12,12
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 10,10
machine_max_jerk_y = 10,10
machine_max_jerk_z = 0.2,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0,0
max_print_height = 150
milling_diameter = 
milling_toolchange_end_gcode = 
milling_toolchange_start_gcode = 
milling_z_lift = 
min_layer_height = 0.07,0.07
min_length = 0.035
nozzle_diameter = 0.4,0.4
parking_pos_retraction = 92
pause_print_gcode = M601
print_host = 
printer_model = 
printer_notes = 
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
printhost_port = 
remaining_times = 0
retract_before_travel = 2,2
retract_before_wipe = 0%,0%
retract_layer_change = 0,0
retract_length = 1,1
retract_length_toolchange = 10,10
retract_lift = 0,0
retract_lift_above = 0,0
retract_lift_below = 0,0
retract_lift_first_layer = 0,0
retract_lift_top = "All surfaces";"All surfaces"
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 30,30
silent_mode = 1
single_extruder_multi_material = 0
start_gcode = ; **** begin start.gcode Replicator 1 Dual Both Extruders****\nM73 P0 ; enable show build progress\nG90 ; set positioning to absolute\nM127 ; disable fan\n;\n; set temps and assert Vref\nM140 S[first_layer_bed_temperature] ; heat bed up to first layer temperature\nM104 S[first_layer_temperature] T0 ;  set right extruder temperature to first layer temperature\nM104 S[first_layer_temperature] T1 ; set left extruder to first layer temperature\nG130 X118 Y118 A118 B118 ; set stepper vrefs to default\n; let the Z stepper vref stay at eeprom level (probably 40)\n;\n; home and set coordinates\nT0 ; home on the right extruder\nG28 X Y Z ; home XYZ at default home feedrates\nG92 X0 Y0 Z0 A0 B0 ; define this as Z=0, the other coords are technically unnecessary but x3g requires them so gpx will make some up\nG1 Z5 F500 ; move Z 5mm away so we can carefully hit the limit switch\nG161 Z F100 ; home Z slowly to give more consistent first layer height\nM132 X Y Z A B; recall stored home offsets for XYZ axes\n;\n; move extruder to waiting position then wait for heatup\nG1 Z30 F1100 ; move Z to waiting height\nG1 X110 Y-72 F2500 ; move to waiting position\nM116 ; wait for everything to reach target temperature\n;\n; wipe and prime left extruder\nT1 ; switch to the left extruder\nG1 Y-75 F2500 ; move off the bed\nG1 Z0 F1100 ; move nozzle to level with bed\nG1 Y-71 F4000 ; chop off any ooze on the front of the bed\nG1 Z[first_layer_height] F1100 ; move to first layer height\nG1 X66 F2500 ; move to prime start position\nG1 X-117 E24 F2000 ; extrude a line of filament across the front edge of the bed (3mm from the front edge)\nG1 Y-68 F2000\nG1 X-104 Y-71 F4000 ; cross the extruded line to close the loop\nG1 X-96 F4000 ; wipe across the line (X direction)\nG1 X-86 Y-76 F6000 ; Move back for an additional wipe (Y direction)\nG92 E0 ; set E to 0 again because the slicer's next extrusion is relative to this 0\n;\n; wipe and prime right extruder\nT0 ; switch to the left extruder\nG1 Y-75 F2500 ; move off the bed\nG1 Z0 F1100 ; move nozzle to level with bed\nG1 Y-69 F4000 ; chop off any ooze on the front of the bed\nG1 Z[first_layer_height] F1100 ; move to first layer height\nG1 X66 F2500 ; move to prime start position\nG1 X-117 E24 F2000 ; extrude a line of filament across the front edge of the bed (3mm from the front edge)\nG1 Y-66 F2000\nG1 X-104 Y-69 F4000 ; cross the extruded line to close the loop\nG1 X-96 F4000 ; wipe across the line (X direction)\nG1 X-86 Y-74 F6000 ; Move back for an additional wipe (Y direction)\nG92 E0 ; set E to 0 again because the slicer's next extrusion is relative to this 0\n;\nM73 P1 ;@body (notify GPX body has started)\n; **** end start.gcode ****
start_gcode_manual = 0
template_custom_gcode = 
thumbnails = 64x64,400x400
thumbnails_color = #018aff
thumbnails_custom_color = 0
thumbnails_with_bed = 0
time_estimation_compensation = 100%
tool_name = ;
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0,0
wipe_advanced = 0
wipe_advanced_algo = linear
wipe_advanced_multiplier = 60
wipe_advanced_nozzle_melted_volume = 120
wipe_extra_perimeter = 0,0
z_offset = 0
z_step = 0.005

[printer:Left Extruder]
bed_custom_model = 
bed_custom_texture = 
bed_shape = -112.5x-72.5,112.5x-72.5,112.5x72.5,-112.5x72.5
before_layer_gcode = 
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = 
default_print_profile = 
deretract_speed = 0
end_gcode = ; **** begin end.gcode Replicator 1 Dual ****\nM73 P100; end build progress\nM127; disable fan\nM140 S0 T0; set bed temperature to 0\nM104 S0 T0; set right extruder temperature to 0\nM104 S0 T1; set left extruder temperature to 0\nG1 Z150 F1100 ; send Z axis to bottom of machine\nT0 ; Next job assumes T0 is the current tool\nM18; disable all stepper motors\nM70 P5 (PRINT COMPLETE)\nM72 P1; Play Ta-Da song\n; **** end end.gcode ****
extra_loading_move = -2
extruder_colour = ""
extruder_fan_offset = 0%
extruder_offset = 0x0
extruder_temperature_offset = 0
fan_kickstart = 0
fan_percentage = 0
fan_speedup_overhangs = 1
fan_speedup_time = 0
feature_gcode = 
gcode_flavor = reprapfirmware
gcode_precision_e = 5
gcode_precision_xyz = 3
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 10000,5000
machine_max_acceleration_extruding = 1500,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_travel = 1500,1250
machine_max_acceleration_x = 9000,1000
machine_max_acceleration_y = 9000,1000
machine_max_acceleration_z = 500,200
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 500,200
machine_max_feedrate_y = 500,200
machine_max_feedrate_z = 12,12
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 10,10
machine_max_jerk_y = 10,10
machine_max_jerk_z = 0.2,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0
max_print_height = 150
milling_diameter = 
milling_toolchange_end_gcode = 
milling_toolchange_start_gcode = 
milling_z_lift = 
min_layer_height = 0.07
min_length = 0.035
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = M601
print_host = 
printer_model = 
printer_notes = 
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
printhost_port = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_lift_first_layer = 0
retract_lift_top = "All surfaces"
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
silent_mode = 1
single_extruder_multi_material = 0
start_gcode = ; **** begin start.gcode Replicator 1 Dual Left Extruder****\nM73 P0 ; enable show build progress\nG90 ; set positioning to absolute\nM127 ; disable fan\n;\n; set temps and assert Vref\nM140 S[first_layer_bed_temperature] ; heat bed up to first layer temperature\nM104 S0 T0 ;  set right extruder temperature to 0\nM104 S[first_layer_temperature] T1 ; set left extruder to first layer temperature\nG130 X118 Y118 A118 B118 ; set stepper vrefs to default\n; let the Z stepper vref stay at eeprom level (probably 40)\n;\n; home and set coordinates\nT0 ; home on the right extruder\nG28 X Y Z ; home XYZ at default home feedrates\nG92 X0 Y0 Z0 A0 B0 ; define this as Z=0, the other coords are technically unnecessary but x3g requires them so gpx will make some up\nG1 Z5 F500 ; move Z 5mm away so we can carefully hit the limit switch\nG161 Z F100 ; home Z slowly to give more consistent first layer height\nM132 X Y Z A B; recall stored home offsets for XYZ axes\n;\n; move extruder to waiting position then wait for heatup\nG1 Z30 F1100 ; move Z to waiting height\nG1 X110 Y-72 F2500 ; move to waiting position\nT1 ; switch to the left extruder\nM116 ; wait for everything to reach target temperature\n;\n; wipe and prime extruder\nG1 Y-75 F2500 ; move off the bed\nG1 Z0 F1100 ; move nozzle to level with bed\nG1 Y-71 F4000 ; chop off any ooze on the front of the bed\nG1 Z[first_layer_height] F1100 ; move to first layer height\nG1 X66 F2500 ; move to prime start position\nG1 X-117 E24 F2000 ; extrude a line of filament across the front edge of the bed (3mm from the front edge)\nG1 Y-68 F2000\nG1 X-104 Y-71 F4000 ; cross the extruded line to close the loop\nG1 X-96 F4000 ; wipe across the line (X direction)\nG1 X-86 Y-76 F6000 ; Move back for an additional wipe (Y direction)\nG92 E0 ; set E to 0 again because the slicer's next extrusion is relative to this 0\nM73 P1 ;@body (notify GPX body has started)\n; **** end start.gcode ****
start_gcode_manual = 0
template_custom_gcode = 
thumbnails = 64x64,400x400
thumbnails_color = #018aff
thumbnails_custom_color = 0
thumbnails_with_bed = 0
time_estimation_compensation = 100%
tool_name = ""
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
wipe_advanced = 0
wipe_advanced_algo = linear
wipe_advanced_multiplier = 60
wipe_advanced_nozzle_melted_volume = 120
wipe_extra_perimeter = 0
z_offset = 0
z_step = 0.005

[printer:Right Extruder]
bed_custom_model = 
bed_custom_texture = 
bed_shape = -112.5x-72.5,112.5x-72.5,112.5x72.5,-112.5x72.5
before_layer_gcode = 
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = 
default_print_profile = 
deretract_speed = 0
end_gcode = ; **** begin end.gcode Replicator 1 Dual ****\nM73 P100; end build progress\nM127; disable fan\nM140 S0 T0; set bed temperature to 0\nM104 S0 T0; set right extruder temperature to 0\nM104 S0 T1; set left extruder temperature to 0\nG1 Z150 F1100 ; send Z axis to bottom of machine\nT0 ; Next job assumes T0 is the current tool\nM18; disable all stepper motors\nM70 P5 (PRINT COMPLETE)\nM72 P1; Play Ta-Da song\n; **** end end.gcode ****
extra_loading_move = -2
extruder_colour = ""
extruder_fan_offset = 0%
extruder_offset = 0x0
extruder_temperature_offset = 0
fan_kickstart = 0
fan_percentage = 0
fan_speedup_overhangs = 1
fan_speedup_time = 0
feature_gcode = 
gcode_flavor = reprapfirmware
gcode_precision_e = 5
gcode_precision_xyz = 3
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 10000,5000
machine_max_acceleration_extruding = 1500,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_travel = 1500,1250
machine_max_acceleration_x = 9000,1000
machine_max_acceleration_y = 9000,1000
machine_max_acceleration_z = 500,200
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 500,200
machine_max_feedrate_y = 500,200
machine_max_feedrate_z = 12,12
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 10,10
machine_max_jerk_y = 10,10
machine_max_jerk_z = 0.2,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0
max_print_height = 150
milling_diameter = 
milling_toolchange_end_gcode = 
milling_toolchange_start_gcode = 
milling_z_lift = 
min_layer_height = 0.07
min_length = 0.035
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = M601
print_host = 
printer_model = 
printer_notes = 
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
printhost_port = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_lift_first_layer = 0
retract_lift_top = "All surfaces"
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
silent_mode = 1
single_extruder_multi_material = 0
start_gcode = ; **** begin start.gcode Replicator 1 Dual Right Extruder****\nM73 P0 ; enable show build progress\nG90 ; set positioning to absolute\nM127 ; disable fan\n;\n; set temps and assert Vref\nM140 S[first_layer_bed_temperature] ; heat bed up to first layer temperature\nM104 S[first_layer_temperature] T0 ;  set right extruder temperature to first layer temperature\nM104 S0 T1 ; set left extruder to 0\nG130 X118 Y118 A118 B118 ; set stepper vrefs to default\n; let the Z stepper vref stay at eeprom level (probably 40)\n;\n; home and set coordinates\nT0 ; home on the right extruder\nG28 X Y Z ; home XYZ at default home feedrates\nG92 X0 Y0 Z0 A0 B0 ; define this as Z=0, the other coords are technically unnecessary but x3g requires them so gpx will make some up\nG1 Z5 F500 ; move Z 5mm away so we can carefully hit the limit switch\nG161 Z F100 ; home Z slowly to give more consistent first layer height\nM132 X Y Z A B; recall stored home offsets for XYZ axes\n;\n; move extruder to waiting position then wait for heatup\nG1 Z30 F1100 ; move Z to waiting height\nG1 X110 Y-72 F2500 ; move to waiting position\nM116 ; wait for everything to reach target temperature\n;\n; wipe and prime extruder\nG1 Y-75 F2500 ; move off the bed\nG1 Z0 F1100 ; move nozzle to level with bed\nG1 Y-71 F4000 ; chop off any ooze on the front of the bed\nG1 Z[first_layer_height] F1100 ; move to first layer height\nG1 X66 F2500 ; move to prime start position\nG1 X-117 E24 F2000 ; extrude a line of filament across the front edge of the bed (3mm from the front edge)\nG1 Y-68 F2000\nG1 X-104 Y-71 F4000 ; cross the extruded line to close the loop\nG1 X-96 F4000 ; wipe across the line (X direction)\nG1 X-86 Y-76 F6000 ; Move back for an additional wipe (Y direction)\nG92 E0 ; set E to 0 again because the slicer's next extrusion is relative to this 0\nM73 P1 ;@body (notify GPX body has started)\n; **** end start.gcode ****
start_gcode_manual = 0
template_custom_gcode = 
thumbnails = 64x64,400x400
thumbnails_color = #018aff
thumbnails_custom_color = 0
thumbnails_with_bed = 0
time_estimation_compensation = 100%
tool_name = ""
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
wipe_advanced = 0
wipe_advanced_algo = linear
wipe_advanced_multiplier = 60
wipe_advanced_nozzle_melted_volume = 120
wipe_extra_perimeter = 0
z_offset = 0
z_step = 0.005

[physical_printer:Makerbot Replicator Dual]
host_type = octoprint
preset_name = Right Extruder
print_host = octopi.local
printer_technology = FFF
printhost_apikey = 8396A428B5F5453E8C69EB11E5C5CA80
printhost_authorization_type = key
printhost_cafile = 
printhost_password = 
printhost_port = 
printhost_user = 

[presets]
print = 0.20mm QUALITY - Makerbot
sla_print = 
sla_material = 
printer = Right Extruder
filament = Generic PLA - Makerbot
physical_printer = Makerbot Replicator Dual